မင်္ဂလာပါ!

လှိုက်လှဲစွာကြိုဆိုပါသည်။ ယခု ပထမဆုံးအကြိမ် ရောက်ဖူးခြင်းဖြစ်ပါသလား? ဝင်ရောက် ဆွေးနွေး မေးမြန်းလိုပါလျှင် အောက်တွင်ဖော်ပြထားသော button များမှတဆင့် ဝင်ရောက် ဆွေးနွေးနိုင်သကဲ့သို့ အဖွဲ့ဝင်အသစ်အနေဖြင့်လည်း လျှောက်ထားနိုင်ပါတယ်။

MYSTERY ZILLION တွင် English သို့မဟုတ် Unicode ဖြင့်သာ အသုံးပြုခွင့်ရှိသည်။ ဇော်ဂျီ ၊ ဧရာ စသည်တို့ကို အသုံးပြုခွင့် မရှိ။ Unicode fonts များမှာ Mon3,Yunghkio, Myanamr3 စသည်များ အသုံးပြုနိုင်သည်။ Unicode Guide ကို ဒီမှာ Download ချပါ။ Zawgyi to Unicode Converter
Don't share ebook or software if nobody request. You can find free book websites on here. We are welcome for discussion or asking question instead.

add more than 4 network adapters on vmware workstation or virtualbox.

i want to add more than 4 network adapters on vmware workstation or virtualbox.how do i do?

Thanked by 1 illikintann

မှတ်ချက်များ

  • Registered Users

    https://pubs.vmware.com/workstation-9/index.jsp?topic=%2Fcom.vmware.ws.using.doc%2FGUID-51725F2A-6D91-4AEA-BDD1-0FAB16676546.html

    https://vmware.com/support/ws55/doc/ws_net_configurations_changing_vadapters.html

    Solutions found from internet. I"m not sure it's what you are after.
    just try it out.

    To add a new virtual Ethernet adapter, follow these steps.

    1. Be sure the virtual machine to which you want to add the adapter is powered off.

    2. Open the virtual machine settings editor (VM > Settings).

    3. Click Add.

    4. The Add Hardware Wizard starts. Select Network Adapter. Click Next.

    5. Select the network type you want to use — Bridged, NAT, Host-only or Custom.

    6. If you select Custom, choose the VMnet network you want to use from the drop-down list.

    Note: Although VMnet0, VMnet1 and VMnet8 are available in this list, they are normally used for bridged, host-only and NAT configurations, respectively. Special steps are required to make them available for use in custom configurations. You should choose one of the other switches.

    1. Click Finish. The new adapter is added.

    2. Click OK to save your configuration and close the virtual machine settings editor.

    To change the configuration of an existing virtual network adapter, follow these steps.

    1. Open the virtual machine settings editor (VM > Settings).

    2. Select the adapter you want to modify.

    3. Select the network type you want to use — Bridged, NAT, Host-only or Custom.

    4. If you select Custom, choose the VMnet virtual network you want to use for the network from the drop-down list.

    5. Click OK to save your changes and close the virtual machine settings editor.

    6. Be sure the guest operating system is configured to use an appropriate IP address on the new network. If the guest is using DHCP, release and renew the lease. If the IP address is set statically, be sure the guest has an address on the correct virtual network.

    Thanked by 1 illikintann
Sign In or Register to comment.